Reducing Energy Consumption During The Cutting Process Of Plywood

Cutting, as the most widely used machining process, is applied in both primary and secondary wood processing. Optimum cutting conditions that result in the high quality of the machined surface and low energy consumption are crucial for wood processing. The effects of the feed speed, cutting speed and average chip thickness on the energy consumption and surface temperature of a circular saw blade during the cutting process of plywood will be described in this paper. By Jozef Fekiač, Ján Svoreň, Jozef Gáborík and Miroslav Němec, Technical University in Zvolen

Circular saws are the most frequently used machines in primary and secondary wood processing. They are designed for transverse cutting (cutting in the direction perpendicular to the fibres) and longitudinal cutting (cutting in the direction of the wood fibres). 

When using forest resources, crosscutting to a preliminary dimension is often used, such as when cutting trunks to planks and producing various wood products. 

Krilek et al. report that lower values of cutting power were measured in the transverse cutting of prisms from (soft) coniferous tree species (spruce) than in the case of (hard) broadleaved tree species (beech). 

The face angle (γ = −5 degrees; 0 degree; 20 degrees) has a great influence on the cutting power. The lowest values of cutting power were achieved at different feed speeds in the case of the face angle γ = 20 degrees. 

In their work, Kminiak and Kubš also report the different effects of (soft) coniferous tree species (spruce) and (hard) broadleaved tree species (beech and oak) on the cutting power when cross-cutting lumber. 

So far, little attention has been paid to the cutting process in primary wood processing (i.e., lumber production). 

Energy consumption and waviness increase with an increasing feed speed and cutting height. Similar conclusions were drawn by Cristóvão et al.

Among several monitored parameters, the thickness of a particle and the cutting direction significantly affects the magnitude of the main cutting force. Other parameters such as wood density, wood moisture and cutting wedge face angle have a lower effect.

Most of the research on the cutting process is focused on secondary wood processing (i.e., production of wood products). 

Research on optimal woodworking conditions showed that the cutting process is influenced by three basic factors: factors related to the type of wood, the technical equipment and the factors including the water absorption coefficient. 

Sawing wood is affected by specific properties of the workpiece (material—hard or soft wood; agglomerated materials—particleboard, MDF, plywood, etc.; moisture; density; temperature, etc.), circular saw blade (face angle γ, back angle α, cutting wedge angle β, cutting speed vc, etc.), feed (feed speed vf, cutting height H, overlap f, etc.) and a combination of factors. 

The effect of these factors on energy consumption has been investigated. When using circular saws, the corrugation of the machined surface is affected by cutting parameters such as cutting height and feed speed. 

Dynamic behaviour, oscillation and deflection of the circular saw blade from the cutting plane are other factors that affect the undulation of the machined surface. 

Research on the effect of vibration and deflection of the circular saw blade on the corrugation of the machined surface has not yet been sufficiently carried out. This means that the influences of various cutting factors on the deflection and waviness of the machined surface have not yet been thoroughly investigated and require further research. 

Heating in the tooth part during the cutting process is one of the factors that influences the oscillation and deflection of circular saw blades. 

The most significant obstruction during cutting is its aberration (deformation) in a plane. This effect is only caused by compressive stress in the circular saw blade, which is dependent on the temperature distribution status inside. 

Knowing the accurate temperature distribution is one of the main ways of solving this problem. The measurement of the tool surface temperature during a high cutting speed (vc = 50 to 100 m/s) is not easy. The use of a thermocouple with a diameter wire d = 0.125 to 0.15 mm was applied. 

The optimal machining of wood and wood materials is a multi-parameter problem when low energy consumption, low noise emission and low dust emission versus high cutting accuracy, tool life and high productivity of the cutting process are required. 

The main goal of this article is to determine the effect of circular saw blade treatment and weight reduction in plywood on the energy consumption (cutting power) of a circular saw and the heating temperature of a circular saw blade. The range of monitored feed and cutting speeds was designed to meet extreme cutting conditions during secondary wood processing.

 

Types Of Plywood

In furniture manufacturing, plywood is mainly used as a filling material in frame constructions, as a construction material for the frames of upholstered furniture or as worktops in kitchen furniture. 

In recent years, the trend of producing lightweight wood-based materials has begun. Lightweight materials result from the change in structure and density in the cross-section of a board or a combination of wood materials with plastics. 

Despite their reduced density, lightweight wood materials show satisfactory mechanical and thermal insulation properties.

In the experiments, two types of plywood were used: non-lightweight (classic) plywood and lightweight plywood. The weight was reduced by incorporating air gaps into the construction of plywood. 

Air gaps (100 mm wide) were located in the transverse layers of the plywood. The plywood was made of beech veneers with a thickness of 2 mm. The adhesive PVAc D3 was used, and the plywood was cold pressed at the temperature of 19 ± 1 degree C. 

The overall view and construction of the tested plywood materials were recorded. From the produced plywood materials, test specimens with dimensions of length = 1000 mm, width = 500 mm and thickness = 14 mm were made.

The physical and mechanical properties of the plywood used in the experiments. The bending properties were determined according to the STN EN 310 and density according to the STN EN 323.

 

Tools & Equipment

In the experiment, two circular saw blades with cutting inserts with tungsten carbide for wood manufactured by Stelit Ltd. Trenčín, the Slovak Republic were used. 

The material of the circular saw blades was steel (DIN 75Cr1, EN 1.2003). There were radial and tangential compensating slots in the body terminated by holes and filled with copper threads. 

The teeth of the circular saw blades had irregular tooth pitch and were alternately slanted grinds. CSB2 (circular saw blades 2) differed from CSB1(circular saw blades 1) in the surface treatment and the length of the cutting edge. 

The circular saw blade CSB1 was not surface treated. The surface of the circular saw blade CSB2 was altered by a powder coating RAL 9006 from the producer Tiger LACQUER SLOVAKIA Ltd. Pezinok, the Slovak Republic. 

The sprayed sides with a thickness of 100 µm were fired in a kiln for 20 min at a temperature of 192 degrees C. We chose the surface treatment by powdering on the basis of preliminary experiments.

A full factorial experimental design resulted in six different machining treatments. The experiment was conducted with six replicates for each treatment.

The average chip thickness in orthogonal cutting and parallel to the fibre direction with a circular saw blade were calculated.

The experiment was carried out using an experimental single-shaft circular saw located in the laboratory of the Faculty of Technology in the workshops of the Technical University in Zvolen, Zvolen Slovak Republic. 

The machine is especially used for the integrated production of semi-finished components and the research. 

The construction of the machine is compact; the main supporting part of the machine is a frame welded from a plate steel material. 

The circular saw cutting mechanism is attached to the frame by screw connections. The high-speed part of the cutting mechanism (shaft) is mounted in radial ball bearings in the bearing housings. 

The feeding mechanism of the circular saw consists of a belt conveyor and an upper roller feeder specific type MW 102 from TOS Svitavy inc, Svitavy, Czech Republic. 

The feed speed of the belt conveyor is continuously variable by means of an electric drive conversion unit in the range from vf = 4 to 40 m/min. The feed speed of the upper roller feeder is gradually variable by means of a gearbox from vf = 4 to 34 m/min. The moving parts of the machine are mounted in plain bushes or ball bearings. The drive of the circular saw shaft is ensured by an electric motor, pulleys and V-belts. The electric motor has a power of P = 5.5 kW, n = 2910 per min. A smooth change of shaft speed is ensured by using a frequency converter. In this experiment, the circular saw was connected to a mobile sawdust extractor type U 1500.

 

Cutting Power Consumption & Surface Temperature

The apparatus at the measuring cutting power and temperature was constructed at the Department of Production and Automation Technology at the Technical University in Zvolen, Zvolen, Slovak Republic. 

The cutting power was monitored by measuring the change in the electric current output from the frequency converter and that consumed by the electric motor of the circular saw. 

The power measurement was provided by a frequency converter, while the active power input without losses and the power of the electric motor were evaluated following the current, voltage and efficiency of the electric motor. 

Recording the measured power quantities meant that they could be read, displayed, and saved in a computer via VDS software (Vonsch Drive Studio, Version 2.20), Brezno, Slovakia. An illustrative example of the display of measured values has been shown according to the program. The computer was connected to the measuring apparatus by a serial USB (Universal Serial Bus) interface. 

By this measuring device, 20 power values per second were generated. Individual measurements of the specimens lasted for more than two s, providing 50 to 100 values. The idle values prior to and after cutting were considered. The values were modified for further processing. 

Thus, the only values recorded when idling and when cutting were selected. These values are considered important. Following the values, the mean value of each cutting condition was calculated.

The temperature distribution in the circular saw blade is determined by the following factors: friction in the cutting process and heat dissipation from the saw blade surface. 

A Pixsys/Calex PUA8-CF device was used to measure the temperature. Pixsys/Calex PUA8-CF devices are industrial infrared contactless temperature sensors with standardised current outputs and USB connections. 

Small dimensions, adjustable emissivity, good accuracy, and linearity over the entire range of operating temperatures are considered the advantages of this device. A USB connection is used to set sensor parameters quickly and easily, as well as for direct connection to a computer. 

Values such as a measuring range corresponding to analogue output, emissivity, etc., can be set. The sensor can work when it is connected to an analogue output (powered by a Pixsys power terminal) or with a connected USB, or with both outputs connected.

The temperature sensor was set to three positions relative to the centre of the circular saw blade. From the temperature values obtained under the same cutting conditions, we calculated the arithmetic mean.

The measured sets of values of the power input of the electric motor of the circular saw drive, as well as the sets of values of the surface temperature of the saw blades, were pre-processed in the Excel program. 

The cutting power values were further processed in the Statistics 12 program. The mean values from six repeated measurements are given in the figures showing the dependence of the cutting power on the individual parameters. The mean values from two repeated measurements are mentioned in the figures showing the dependence of the surface temperature of the circular saw blades on the individual parameters.

 

Cutting Power Consumption

Following the program Statistics 12, it can be stated that all studied cutting factors have a significant effect on the consumption of cutting power at a significance level of 0.95. Thus, the value of the cutting power is affected by the construction of the material (plywood), the construction of the circular saw blade and the feed speed. 

According to the program Statistics 12, the material construction (plywood) was the factor with the greatest impact on the cutting performance. The design of the circular saw blade was the second most important factor affecting the cutting performance. 

The effect of feed speed and circular saw blade design on cutting power is shown. An increase in the feed rate from vf = 14 to 28 m/min resulted in the cutting power increasing from 26 percent to 32 percent. Similar results are reported by other authors in their works. 

The lightweight construction of the material (plywood) compared to conventional material (classic plywood) reduced the cutting power values by an average of 19.0 percent when using CSB1 and by an average of 22.0 percent when using CSB2. The measured values of the cutting power show that the values of the cutting power can be influenced both by the construction of the material and by changing the construction of the saw blade. Through the interaction of these parameters, an average saving of 34 percent in the cutting power of the circular saw can be achieved.

Average chip thickness, as a critical factor in the sawing process, significantly affects the cutting power. An increase in the cutting power in average chip thickness in the case of both examined cut materials (classic and lightweight plywood) is shown. 

The dependence is mentioned in other scientific work. The experiment results also shows that the highest coefficient of determination obtained between the cutting power and the average chip thickness was achieved in the case of classic plywood using a CSB2 circular saw blade (r2 = 99 percent). 

A very high tightness is ensured by the value (80 percent ≤ r2). A lower coefficient of determination between the cutting power and the average chip thickness was achieved in the case of lightweight plywood compared to classic plywood using a circular saw blade CSB1 (r2 = 82 percent and 90 percent). Our calculation through related equation shows that in the case of both materials, an increase in the feed speed corresponds to an increase in the chip thickness, which results in higher cutting power.

 

Circular Saw Blade Surface Temperature

The adverse effect of the heating of the circular saw blade in the cutting zone and thus the resulting temperature difference between the central hole and the edge of the circular saw blade caused increased variability in the cutting process. 

Lehmann (who mentioned heating and cooling of circular saws in Canada) also emphasised that the temperature differences of the circular saw blade between the edge and the centre hole have a fundamental effect on its rigidity. 

Therefore, it is necessary to measure the temperature of the circular saw blade both at the time, in the middle of the radius and at the centre hole. This demonstrates the heating and cooling principles of the circular saw blade. 

The temperature sensor was set to three positions relative to the centre of the circular saw blade. From the temperature values obtained under the same cutting conditions, we calculated the arithmetic mean.

The dependence of the surface temperature of the circular saw blades has been shown on the feed speed at the rotation speed n = 4050 per min. The surface temperatures of the circular saw blades CSB1 and CSB2 had values at about 24.5 ± 0.2 degrees C at the sensor position of 65 mm from the shaft axis (near the flanges). These temperatures increased slightly with increasing feed speed to the values of 25 to 26.5 degrees C.

Based on experimental measurements, other authors reported similar temperature values in the range between 22 and 24 degrees C for the area of clamping flanges. 

At the position of the temperature sensor of 110 mm from the shaft axis, there was a significant increase in the surface temperatures of the discs to values of 25 to 26.5 degrees C. At the last position of the sensor closest to the heel circle of the teeth, (R = 155 mm) from the shaft axis, the surface temperature of the CSB1 reached 31.5 degrees C. 

Mohammadpanah et al. state a temperature of 33 degrees C for the area of the heel circle of teeth. The circular saw blade CSB2, which had a powder-coated coating applied to the surface, differed significantly in temperature from CSB1, mainly in the area R = 155 mm. 

The highest temperature gradient between the areas R = 155 mm and R = 65 mm was at a feed speed of 28 m/min. In the case of CSB1, this value is 5.0 degrees C, and in the case of CSB2, it is 1.0 degree C. Compared to the temperature gradient of CSB2 (1.0 degree C), there is a big difference. 

This difference in temperature gradient may be one of the parameters that caused the different dynamic behaviour of CSB2.

The dependence of the temperature on the surface of the circular saw blades from the distance of the temperature sensor from the axis of the saw blades (shaft) was at the rotation speed n = 4150 per min.

It can be seen that the surface temperatures of the saw blades differ. In all cases of feed speed, the values of the modified circular saw blade CSB2 are lower than the values of the conventional circular saw blade CSB1. The highest difference between the surface temperature of the circular saw blades is at the position of the temperature sensor from the shaft axis (R = 155 mm) and the feed speed vf = 28 m/min, which is about 5 degrees C. 

Besides, it can be stated that the temperature gradient between the sensor positions 155 mm and 65 mm is not uniform; there is most likely an exponential dependence. The same conclusions are drawn by other authors. 

When comparing circular saw blades CSB1 and CSB2, it can be seen that the temperature gradient is similar, but the CSB2 differs in lower temperature values at each position of the sensor.

As has already been mentioned, the average chip thickness is a decisive factor in the sawing process, as it has a significant effect on the cutting power and the surface temperature of the circular saw blade. And there’s an increase in the surface temperature of the saw blades in the average chip thickness in the case of the materials studied (classic and lightweight plywood).

The highest coefficient of determination between the surface temperature and the average chip thickness was obtained in the case of the lightweight plywood using a CSB1 circular saw blade (r2 = 97 percent). It also shows that the high tightness is ensured by the value 80 percent ≤ r2. The lowest coefficient of determination between the surface temperature of the circular saw blade and the average chip thickness was obtained in the case of classic plywood using the circular saw blade CSB2 (r2 = 73 percent). 

Our calculation through equation has shown that in the case of both materials, an increase in the feed speed rate corresponds to an increasing chip thickness, which results in a higher value of the circular saw blade surface temperature. The correlation between the consumed cutting power and the temperature of the circular saw blades surface, depending on the size of the average chip thickness, is demonstrated.

 

Precondition To Reducing Energy

The effect of circular saw blade treatment, the type of material (classic and lightweight plywood), feed speed, and average chip thickness on the consumed cutting power and surface temperature of circular saw blades during cutting using an experimental single-shaft circular saw was evaluated in this paper.

In the whole range of the feed speed of 14 to 28 m/min, the values of the cutting power were lower in the case of the cut material (lightweight plywood) compared to the material (classic plywood) at both revolutions of the circular saw shaft. The average value represented a 20 percent reduction.

The treatment of the circular saw blade (CSB2) reduced the cutting power by 14.7 percent to 22.7 percent when cutting classic plywood and by 18.3 percent to 25.7 percent when cutting lightweight plywood.

Following the measurement results, the surface temperature of the circular saw blade depended on the type of material cut. Lower values were obtained when lightweight plywood was cut. The maximum temperature difference in the case of the unmodified (conventional) circular saw blade CSB1 was T = 2.3 degrees C, and in the case of the modified circular saw blade CSB2, it was T = 0.5 degrees C.

There was a significant increase in the surface temperature at the outer edge of the circular saw blade (R = 155 mm) depending on the feed speed. The individual circular saw blades differed from each other in the magnitude of the temperature drop.

In the case of the CSB1 circular saw blade, the temperature drop was ΔT = 5.0 degrees C; in the case of the CSB2 circular saw blade, it was ΔT = 1.0 to 2.0 degrees C. The surface temperature profile of the circular saw blades had an assumed exponential course from the edge to the flange area. 

The difference in the temperature gradient of the two circular saw blades was probably one of the reasons for the change in the dynamic behavior of CSB2 in the cutting process, which was ultimately reflected in its lower values of cutting power.

An increase in the value of the average chip thickness in the range of 0.058 to 0.119 mm resulted in an increase in the cutting power and the surface temperature of the circular saw blades in the process of cutting classic and lightweight plywood. All experiments performed showed the correlation between the consumed cutting power and the surface temperature of the circular saw blades depending on the size of the average chip thickness.

The practical use of the presented results gives the precondition to reduce the energy balance of the process of cutting wood materials. 

Further research should focus on ex-tending the experiment to the process of cutting other lightweight wood materials as well.

Rate this item
(0 votes)

FDMAsia About Us

For almost 30 years, FDM Asia has been the publication of choice for woodworking professionals in Asia Pacific, providing the latest news and expert insights of a diverse range of topics including process technologies, furniture production, panels manufacturing, raw materials handling and sustainability issues.

We have one of the most comprehensive woodworking database and e-media programme to assist you in your e-marketing and give you an exclusive opportunity to connect to our 25,152 online subscribers.